for board-to-board or interface for pcb right-angle smt right-angle smt type 32-contacts male board connector rmc-ea32pmy-om15-xma( )b( ) configuration of product part no. rmc -ea 32 p my - om15 -xma( )b( ) ????? ? ? ? series name ? ea: emi-filtered , contact, locking hardware, hold down, one-piece molded ? no. of contacts: 32 (30 + 2 contacts) ? p: with location pegs ? my: smt type, male ? off-set onboard type a type b type ? forms and locations of plarigation key xmab : a type: key-less, b type: key-less xma3b3 :a type: key 3, b type: key 3 xma2b3 :a type: key 2, b type: key 3 xma1b3 :a type: key 1, b type: key 3 mating connectors : refer to the table shown ? ? ? ? ? ? components ? ? ? ? ? ? ?alternately, this connector can mate with rmc-15 contact type female cable connectors. ?this is a combined rmc-ea15my type connector that has two power source contacts at the center. 0.814=11.2 0.814=11.2 rmc-ea32pmy-om( )-xma1b3 rmc-ea32pmy-om( )-xma2b3 rmc-ea32pmy-om( )-xma3b3 rmc-e30fy1a-xma23b12 rmc-e30fy1a-xma13b12 rmc-e30fy1a-xma12b12 locations of polarization keys part no. key location key location identification identification b3 b3 b3 a1 a2 a3 1 2 3 3 3 3 mating connectors 031 0.814=11.2 0.814=11.2 46.6 44.76 43.8 43.1 41.6 36.5 2.54=10 2.54=10 26.5 7 0.5 0.15 1.8 3.1 3.3 5.3min. 5.8min. 2.4 2.4 0.8 0.05 0.7 1.2 2.4 0.8 0.05 ?.2 : pad (through-hole) edge of pcb pad (16 places) pos.#b1 pos.#p1 pos.#p2 pos.#a15 11.4 0.1 pos.#a1 pos.#b15 connector mating surface 2.15 (4.7) 1.25 2.5 0.1 0.1 pcb layout for reference only t = 1.0 mm 46.1 0.814=11.2 0.814=11.2 14.8 1.55 7 2.9 2 14.8 0.8 0.8 0.8 0.25 0.4 1.2 11.4 41.6 0.8 46.1 44 26.5 pos.#p1 pos.#a15 pos.#a15 pos.#a1 pos.#a1 pos.#b1 pos.#b1 pos.#b15 123 123 pos.#b15 1 1 (0.8) a type b type (0.9) 3.7 (2.15) 0.8 0.2 4.5 pos.#p2 4.6 a1 a15 p1 p2 b1 b15 japan pmy15 honda ?when using this model for multi-function card for lan and modem, a variation type connector without the central power source contacts is also available. ?some models may not be quickly supplied depending on the contiguration of part number (key position and off-set dimension). for the availability of the model required, consult your supplier. ?use as an board to board connector. locking hardware insulator shell hold down contacts contacts for power supply others wire wrapping crimping soldering idc press-in smt dip
|
